VGV7519.dtsi 6.86 KB
Newer Older
1 2 3 4 5 6 7
/include/ "vr9.dtsi"

/ {

    model = "VGV7519 - KPN Experiabox V8";

	chosen {
8
		bootargs = "console=ttyLTQ0,115200 init=/etc/preinit maxvpes=1 maxtcs=1 phym=64M mem=62M panic=1 vpe1_load_addr=0x83e00000 vpe1_mem=2M vpe1_wired_tlb_entries=1";
9 10 11 12 13
	};

	memory@0 {
		reg = <0x0 0x4000000>;
	};
14 15 16 17 18 19 20 21 22

	sram@1F000000 {
		vmmc@107000 {
			status = "okay";
			gpios = <&gpio 30 0  //fxs relay
				 &gpio 31 0  //still unknown
				 &gpio 3 0>; //reset_slic?
		};
	};
23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
	
	fpi@10000000 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "lantiq,fpi", "simple-bus";
		ranges = <0x0 0x10000000 0xEEFFFFF>;
		reg = <0x10000000 0xEF00000>;

		localbus@0 {
			#address-cells = <2>;
			#size-cells = <1>;
			compatible = "lantiq,localbus", "simple-bus";
		};

		gpio: pinmux@E100B10 {
			compatible = "lantiq,pinctrl-xr9";
			pinctrl-names = "default";
			pinctrl-0 = <&state_default>;
			
			interrupt-parent = <&icu0>;
			interrupts = <166 135 66 40 41 42 38>;

			#gpio-cells = <2>;
			gpio-controller;
			reg = <0xE100B10 0xA0>;

			state_default: pinmux {
				stp {
					lantiq,groups = "stp";
					lantiq,function = "stp";
				};
				spi {
blogic's avatar
blogic committed
55
					lantiq,groups = "spi";
56 57 58 59 60 61
					lantiq,function = "spi";
				};
				mdio {
					lantiq,groups = "mdio";
					lantiq,function = "mdio";
				};
blogic's avatar
blogic committed
62 63
				gphy-leds_out {
					lantiq,pins = "io7", "io44";
64 65 66
					lantiq,pull = <0>;
					lantiq,output = <1>;
				};
blogic's avatar
blogic committed
67 68 69 70 71 72 73 74 75
				stp_out {
					lantiq,pins = "io4", "io5", "io6";
					lantiq,open-drain = <0>;
					lantiq,output = <1>;
					lantiq,pull = <0>;
				};
				pci-rst {
					lantiq,pins = "io21";
					lantiq,open-drain = <0>;
76 77 78
					lantiq,pull = <0>;
					lantiq,output = <1>;
				};
blogic's avatar
blogic committed
79 80 81 82 83 84
				gphy-leds {
					lantiq,groups = "gphy0 led1", "gphy1 led0";
					lantiq,function = "gphy";
					lantiq,open-drain = <0>;
					lantiq,pull = <0>;
					lantiq,output = <1>;
85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196
				};
			};
		};

		eth@E108000 {
			#address-cells = <1>;
			#size-cells = <0>;
			compatible = "lantiq,xrx200-net";
			reg = <	0xE108000 0x3000 /* switch */
				0xE10B100 0x70 /* mdio */
				0xE10B1D8 0x30 /* mii */
				0xE10B308 0x30 /* pmac */
			>;
			interrupt-parent = <&icu0>;
			interrupts = <73 72>;

			lan: interface@0 {
				compatible = "lantiq,xrx200-pdi";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0>;
				mac-address = [ 00 11 22 33 44 55 ];

				ethernet@0 {
					compatible = "lantiq,xrx200-pdi-port";
					reg = <0>;
					phy-mode = "rgmii";
					phy-handle = <&phy0>;
				};
				ethernet@1 {
					compatible = "lantiq,xrx200-pdi-port";
					reg = <1>;
					phy-mode = "rgmii";
					phy-handle = <&phy1>;
				};
				ethernet@2 {
					compatible = "lantiq,xrx200-pdi-port";
					reg = <2>;
					phy-mode = "gmii";
					phy-handle = <&phy11>;
				};
				ethernet@4 {
					compatible = "lantiq,xrx200-pdi-port";
					reg = <4>;
					phy-mode = "gmii";
					phy-handle = <&phy13>;
				};
			};

			wan: interface@1 {
				compatible = "lantiq,xrx200-pdi";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <1>;
				mac-address = [ 00 11 22 33 44 56 ];
				lantiq,wan;
				ethernet@5 {
					compatible = "lantiq,xrx200-pdi-port";
					reg = <5>;
					phy-mode = "rgmii";
					phy-handle = <&phy5>;
				};
			};

			mdio@0 {
				#address-cells = <1>;
				#size-cells = <0>;
				compatible = "lantiq,xrx200-mdio";
				phy0: ethernet-phy@0 {
					reg = <0x0>;
					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
				};
				phy1: ethernet-phy@1 {
					reg = <0x1>;
					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
				};
				phy5: ethernet-phy@5 {
					reg = <0x5>;
					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
				};
				phy11: ethernet-phy@11 {
					reg = <0x11>;
					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
				};
				phy13: ethernet-phy@13 {
					reg = <0x13>;
					compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22";
				};
			};
		};

		stp: stp@E100BB0 {
			compatible = "lantiq,gpio-stp-xway";
			reg = <0xE100BB0 0x40>;
			#gpio-cells = <2>;
			gpio-controller;

			lantiq,shadow = <0xffff>;
			lantiq,groups = <0x3>;
			lantiq,dsl = <0x0>;
			lantiq,phy1 = <0x0>;
			lantiq,phy2 = <0x0>;
			/* lantiq,rising; */
		};

		ifxhcd@E101000 {
			status = "okay";
			gpios = <&gpio 32 0>;
			lantiq,portmask = <0x3>;
		};

		pci@E105400 {
blogic's avatar
blogic committed
197
			status = "okay";
198 199 200
			#address-cells = <3>;
			#size-cells = <2>;
			#interrupt-cells = <1>;
blogic's avatar
blogic committed
201
			compatible = "lantiq,pci-xway";
202 203 204 205 206 207 208 209 210 211 212
			bus-range = <0x0 0x0>;
			ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000   /* pci memory */
				0x1000000 0 0x00000000 0xAE00000 0 0x200000>; /* io space */
			reg = <0x7000000 0x8000         /* config space */
				0xE105400 0x400>;       /* pci bridge */
			lantiq,bus-clock = <33333333>;
			/*lantiq,external-clock;*/
			lantiq,delay-hi = <0>; /* 0ns delay */
			lantiq,delay-lo = <0>; /* 0.0ns delay */
			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
			interrupt-map = <
213
				0x7000 0 0 1 &icu0 30 1 // slot 14, irq 30
214
				>;
blogic's avatar
blogic committed
215
			gpio-reset = <&gpio 21 0>;
216 217
			req-mask = <0x1>;	/* GNT1 */
		};
218 219 220 221

		pcie@d900000 {
			status = "disabled";
		};
222 223 224 225
	};

	gphy-xrx200 {
		compatible = "lantiq,phy-xrx200";
226 227
		firmware1 = "lantiq/vr9_phy11g_a1x.bin";	/*VR9 1.1*/
		firmware2 = "lantiq/vr9_phy11g_a2x.bin";	/*VR9 1.2*/
228 229 230
		phys = [ 00 01 ];
	};

blogic's avatar
blogic committed
231 232 233 234 235
	ralink_eep {
		compatible = "ralink,eeprom";
		ralink,eeprom = "RT2860.eeprom";
	};

236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324
	gpio-keys-polled {
		compatible = "gpio-keys-polled";
		#address-cells = <1>;
		#size-cells = <0>;
		poll-interval = <100>;
		reset {
			label = "reset";
			gpios = <&gpio 9 1>;
			linux,code = <0x198>;
		};
		eco {
			label = "eco";
			gpios = <&gpio 41 1>;
			linux,code = <247>;
		};
		rfkill {
			label = "rfkill";
			gpios = <&gpio 45 1>;
			linux,code = <0xf7>;
		};
		wps {
			label = "wps";
			gpios = <&gpio 10 1>;
			linux,code = <0x211>;
		};
	};

	gpio-leds {
		compatible = "gpio-leds";

		eco {					/* blue */
			label = "eco";
			gpios = <&stp 2 1>;
		};
		wps_red {				/* red */
			label = "wps_red";
			gpios = <&stp 3 1>;
		};
		wps_yellow {				/* yellow */
			label = "wps_yellow";
			gpios = <&stp 4 1>;
		};
		upgrade {				/* blue */
			label = "upgrade";
			gpios = <&stp 5 1>;
		};
		tv {					/* yellow */
			label = "tv";
			gpios = <&stp 6 1>;
		};
		internet_yellow {			/* yellow */
			label = "internet_yellow";
			gpios = <&stp 7 1>;
		};
		internet_red {				/* red */
			label = "internet_red";
			gpios = <&stp 8 1>;
		};
		broadband_red {				/* red */
			label = "broadband_red";
			gpios = <&stp 9 1>;
		};
		broadband_yellow {			/* yellow */
			label = "broadband_yellow";
			gpios = <&stp 10 1>;
		};
		voice {					/* yellow */
			label = "voice";
			gpios = <&stp 11 1>;
		};
		wireless_red {				/* red */
			label = "wireless_red";
			gpios = <&stp 12 1>;
		};
		wireless_yellow {			/* yellow */
			label = "wireless_yellow";
			gpios = <&stp 13 1>;
		};
		power2 {				/* yellow */
			label = "power2";
			gpios = <&stp 14 1>;
		};
		power {					/* red */
			label = "power";
			gpios = <&stp 15 1>;
			default-state = "on";
		};
	};
};