- May 21, 2015
-
-
jogo authored
Add it to the appropriate places so the power led properly works and ethernet is properly configured for failsafe. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45709 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
jogo authored
This patch adds support for the Huawei HG655b. Nothing much special in this router, it's just another BCM6368 with a Ralink RT3062 wifi chip and the calibration data embedded in the main flash chip at offset 0x7c0000. There is also configuration data used by the OEM firmware before the cal_data partition, this area is protected by the board_data partition in this patch. Signed-off-by:
Daniel Gonzalez <dgcbueu@gmail.com> Signed-off-by:
-
- May 20, 2015
-
-
cyrus authored
Commit 5168c9a5 introduced a regression during patch application on the 4.0 kernel. Some of the patched content doesn't match the actual code, therefore leading to the following error: Applying patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch patching file net/ipv6/ip6_output.c Hunk #1 FAILED at 886. 1 out of 1 hunk FAILED -- rejects in file net/ipv6/ip6_output.c patching file net/ipv6/route.c Hunk #1 succeeded at 2247 (offset 2 lines). Patch generic/667-ipv6-Fixed-source-specific-default-route-handling.patch does not apply (enforce with -f) This change just adapts the actual patch to fix what is in kernel 4.0 and make it apply cleanly. Signed-off-by:
Mathieu Olivari <mathieu@codeaurora.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45705 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
kaloz authored
Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45704 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- May 19, 2015
-
-
cyrus authored
Signed-off-by:
Steven Barth <steven@midlink.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45699 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- May 17, 2015
-
-
rmilecki authored
Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45694 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- May 16, 2015
-
-
rmilecki authored
This device seems to have switch port 7 connected to the CPU: vlan1ports=1 2 3 5 7* vlan2ports=0 7u it should be handled by eth1 and NVRAM seems to confirm that (no et0macaddr entry, existing et1macaddr & et1phyaddr entries). One of the remaining ports (4/8?) may be connected to the Quantenna SoC. Original firmware boot log contains following messages: (0x00,0x5d)Port 5 States Override: 0xfb (0x00,0x5f)Port 7 States Override: 0xfb (0x00,0x0e)Port 8 States Override: 0x0a (why does it force port 5 state?!) Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45690 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- May 13, 2015
-
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
It has 3 Ethernet interfaces, each of them connected to separated switch port. Default NVRAM uses switch port 8 as CPU which is connected to the 3rd interface (eth2). Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
- May 12, 2015
-
-
rmilecki authored
This chipset has at least 8 usable ports, e.g. Netgear R8000 has ports 5, 7 and 8 connected to Ethernet interfaces: vlan1ports=0 1 2 3 5 7 8* vlan2ports=4 8u Port 6 seems to be always disabled. Signed-off-by:
-
- May 11, 2015
-
-
nbd authored
ar71xx: convert tl-wr741nd v1/v2 to new image building code, add infrastructure for building the loader Signed-off-by:
Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45672 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- May 10, 2015
-
-
nbd authored
Since the kernel/rootfs split handling was modified 2 years ago by r37283 ( https://dev.openwrt.org/changeset/37283 ) and by the subsequent checkins, users have seen rather scary mtd errors in the log at every boot. The message ends "-- forcing read-only", which looks a bit error-like. That error has been mentioned in some forum threads, when users have noticed this message instead of some actual error. [ 2.940000] 0x000000070000-0x000000ff0000 : "firmware" [ 2.970000] 2 netgear-fw partitions found on MTD device firmware [ 2.970000] 0x000000070000-0x000000188440 : "kernel" [ 2.980000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 2.990000] 0x000000188440-0x000000ff0000 : "rootfs" The patch removes the rather useless warning message. signed-off-by:
Hannu Nyman <hannu.nyman@iki.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45669 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
Signed-off-by:
-
nbd authored
Signed-off-by:
-
nbd authored
This change adds PCIe support to IPQ806x based platforms. The driver is actually cherry-picked from the following LKML thread: *https://lwn.net/Articles/643086/ (patches 110-111) We also add here an additional fix to support multiple PCI controllers on the same platform (patch 112), and to patch the ap148 & dbs149 DTS files (patch 113). Signed-off-by:
-
nbd authored
This change enable zImage+appended dtb support in ipq806x kernel options. The zImage will now be generated as part of the kernel binaries. Platforms which do not have DT support enabled in U-boot can now make use of it by generating zImage files and appending dtb to it. It is not used yet but it is done as a stepping stone for early IPQ806x platforms, which did not include DT support in U-boot. Signed-off-by:
-
nbd authored
ARCH_QCOM is using the ARCH_MULTIPLATFORM option, as now recommended on most ARM architectures. This automatically calculate ZRELADDR by masking PHYS_OFFSET with 0xf8000000. On IPQ806x though, the first ~20MB of RAM is reserved for the hardware. In newer bootloader, when DT is used, this is not a problem, we just reserve this memory in the device tree. But if the bootloader doesn't have DT support, then ATAGS have to be used. In this case, the ARM decompressor will position the kernel in this low mem, which will not be in the RAM section mapped by the bootloader, which means the kernel will freeze in the middle of the boot process trying to map the memory. As a work around, this patch allows disabling AUTO_ZRELADDR when ARCH_QCOM is selected. It makes the zImage usage possible on bootloaders which don't support device-tree, which is the case on certain early IPQ806x based designs. Signed-off-by:
-
nbd authored
This option has been added in kernel 3.17. It shows-up only when both ARCH_QCOM and CRYPTO are enabled. So we'll disable these two by default to avoid stalling the build when these conditions are met. Signed-off-by:
-
luka authored
Signed-off-by:
Catrinel Catrinescu <cc@80211.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45656 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
Signed-off-by:
-
- May 09, 2015
-
-
nbd authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
- May 08, 2015
-
-
nbd authored
Signed-off-by:
-
luka authored
Signed-off-by:
Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45648 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
luka authored
Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome > Signed-off-by:
L. D. Pinney <ldpinney@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45647 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
Signed-off-by:
-
nbd authored
Signed-off-by:
-
nbd authored
There are 2 images missing: TLWR2543 TLWR1043V2 which have special properties. v2: set correct DEVICE_PROFILES for all images. v2: migrate TP-LINK TL-WR710N v2 which was committed after v1. v2: split very very long line `TARGET_DEVICES +=` into smaller parts Signed-off-by:
Alexander Couzens <lynxis@fe80.eu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45643 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
Signed-off-by:
Michael J. Bazzinotti <mbazzinotti@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@45640 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
Signed-off-by:
-
nbd authored
Signed-off-by:
-
