- Sep 15, 2013
-
-
hauke authored
This is based on a patch by Mathias Adam. Signed-off-by:
Mathias Adam <m.adam--openwrt@adamis.de> Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38001 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
juhosg authored
Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38000 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
hauke authored
Without this patch it is impossible to read et_swtype, because the 1 byte space is needed for the terminating null byte. Now it should be possible to read decimal and hex vars of max 8 bit. Signed-off-by:
-
hauke authored
Most of the bcm47xx devices use TRX format for storing kernel and some partition like Squashfs or JFFS2. This is pretty flexible solution, CFE (the bootloader) just writes (and later boots) TRX at some hardcoded place and paritions can vary in the size. However some devices don't use TRX format. Very recently we have discovered ZTE H218N that has kernel and rootfs partitions at some "random" places. This patch allows Linux find a rootfs partition after installing custom image with a CFE bootloader. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37998 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
juhosg authored
Separate OpenWrt specific MTD options from the mainline option by moving those into a new submenu in the kernel configuration interface. Signed-off-by:
-
hauke authored
* Use different structs depending on the number of nvram variables to check. * Add detection of ZTE H218N, this closes #14151. Signed-off-by:
-
hauke authored
The revision is stored in a different register than it is in other Broadcom switches. Signed-off-by:
-
hauke authored
These switches are integrated in some recent BCM53XX and BCM47XX SoCs like the BCM53572. Signed-off-by:
-
hauke authored
Some devices (BCM4749, BCM5357, BCM53572) have internal switch that requires initialization. We already have code for this, but because of the typo in code it was never working. This resulted in network not working for some routers and possibility of soft-bricking them. Use correct bit for switch initialization and fix typo in the define. Signed-off-by:
-
- Sep 14, 2013
-
-
nbd authored
Signed-off-by:
Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37990 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
hauke authored
Signed-off-by:
-
hauke authored
The Linksys wrt310n v1 does not have a robo_reset config variable in nvram, but GPIO Pin 8 is the pin needed for resetting the external switch, Linksys hard coded it into their source code. Thank you Devastator for testing. Signed-off-by:
-
hauke authored
Signed-off-by:
-
hauke authored
Thank you Devastator for testing. Signed-off-by:
-
nbd authored
Signed-off-by:
-
nbd authored
Signed-off-by:
-
nbd authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Use the config_enabled() macro where it is possible. Signed-off-by:
-
- Sep 13, 2013
-
-
luka authored
Signed-off-by:
Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37979 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
hauke authored
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37978 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
hauke authored
This patch adds board detection for the Linksys E1000 V2.1 router, as well as GPIO support for same. This fixes bug #14135. Currently, wired networking isn't working on the router, and I haven't tried the wireless, but with this patch, OpenWRT successfully boots, and all the LEDs and buttons work properly. Signed-off-by:
Zachary Catlin <zcatlin@indiana.edu> Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
- change patch numbers to group the related stuff together, - add mtd prefix where it is missing, - use hyphens in the patch names Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
hauke authored
Most of the Linksys devices without an own GPIO configuration where detected as WRT54G. On one board this made OpenWrt to boot into failsafe every time, because one GPIO configurated as button was not a button. Signed-off-by:
-
hauke authored
Thanks Devastator for testing git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37969 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Squashfs is unable to decompress some blocks without that: [ 0.970000] SQUASHFS error: xz_dec_run error, data probably corrupt [ 0.980000] SQUASHFS error: squashfs_read_data failed to read block 0x29a72 [ 0.990000] SQUASHFS error: Unable to read fragment cache entry [29a72] [ 1.000000] SQUASHFS error: Unable to read page, block 29a72, size 14c50 [ 1.010000] SQUASHFS error: Unable to read fragment cache entry [29a72] [ 1.020000] SQUASHFS error: Unable to read page, block 29a72, size 14c50 [ 1.260000] SQUASHFS error: xz_dec_run error, data probably corrupt Signed-off-by:
-
juhosg authored
This patch adds support for building firmware images for the TP-Link TL-MR3040 v2. Tested and working on v2.1 hardware. Signed-off-by:
Mads Hansen <d@taba.se> Signed-off-by:
-
juhosg authored
I checked the GPL code drop from D-Link and tried to get the wireless and LAN switch LEDs to light up. I found some references in AthSDK/www/DIR-825_C1/bsp.h as well as AthSDK/www/DIR-825_C1/rootfs/etc/sysconfig/S2gpio.sh, but in the end I only got the led for 2.4GHz to work. Anyway, here's the patch. Signed-off-by:
Sebastian Kemper <sebastian_ml@gmx.net> Signed-off-by:
-
jow authored
- fixes buffer corruption with JSON-RPC list calls - change JSON-RPC protocol to include the session ID into the call attributes instead of passing it via the URL - forcibly pass effective session ID as "ubus_rpc_session" attribute to called procedures - change ubus acl checking to conform with new ubus session namespace git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37962 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
jow authored
- recalculate session ACLs on reload - support negative access group expressions in /etc/config/rpcd - prevent destryoing the default session - use "ubus_rpc_session" attribute as session identifier to enforce JSON-RPC proxy security git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37961 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
luka authored
Signed-off-by:
-
hauke authored
Signed-off-by:
-
