- Feb 15, 2015
-
-
blogic authored
Signed-off-by:
John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44456 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Feb 14, 2015
-
-
kaloz authored
The current pxa3xx_nand driver doesn't support sub-page writing, so the VID header offset must be specified explicitly. Signed-off-by:
Claudio Leite <leitec@staticky.com> Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44455 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
oops, accidently moved instead of copied them Signed-off-by:
-
blogic authored
ZyXEL NBG6716 "rfkill" is a switch, not a button. Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44453 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Git internals are referenced by .git which isn't necessarily a directory. It may also be a file that references the actual .git directory using the gitdir directive. If .git is assumed to be a directory the build will not be able to get the correct version when openwrt is included as a git submodule because when used as a submodule .git will actually be a file referencing to a subdirectory in the parent's git dir. When the correct version is not detected some image generation tools will fail because the OpenWrt string will be 'OpenWrtunknown' which is too long for some header formats. Signed-off-by:
Felix Kaechele <heffer@fedoraproject.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44452 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Some Lantiq SoCs are not able to use buffered writes properly with Intel command set flash due to the way NOR addresses on EBU are manipulated. This patch disables buffered writes on those devices. The only device affected at the moment is ARV4510PW, others use AMD/Fujitsu command set. Signed-off-by:
Matti Laakso <malaakso@elisanet.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44451 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails. Fix this by using pdev->resource[i].start instead. Signed-off-by:
-
blogic authored
Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44449 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
procd gets last console from cmdline, so swapping tty1 (framebuffer) and ttyAMA0 (uart) is enough to force procd output via uart Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
nico authored
configure tries to guess pagesize by calling getconf, provided by eglibc and compiled for the target, not the host. Signed-off-by:
Nicolas Thill <nico@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44445 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nico authored
Signed-off-by:
-
kaloz authored
Signed-off-by:
-
kaloz authored
Signed-off-by:
-
- Feb 13, 2015
-
-
blogic authored
Signed-off-by:
-
blogic authored
This change adds the configuration options "bssid_whitelist" and "bssid_blacklist" used to limit the AP selection of a network to a specified (finite) set or discard certain APs. This can be useful for environments where multiple networks operate using the same SSID and roaming between those is not desired. It is also useful to ignore a faulty or otherwise unwanted AP. In many applications it is useful not just to enumerate a group of well known access points, but to use a address/mask notation to match an entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00). This is especially useful if an OpenWrt device with two radios is used to retransmit the same network (one in AP mode for other clients, one as STA for the uplink); the following configuration prevents the device from associating with itself, given that the own AP to be avoided is using the bssid 'C0:FF:EE:D0:0D:42': config wifi-iface option device 'radio2' option network 'uplink' option mode 'sta' option ssid 'MyNetwork' option encryption 'none' list bssid_blacklist 'C0:FF:EE:D0:0D:42/00:FF:FF:FF:FF:FF' This change consists of the following cherry-picked upstream commits: b3d6a0a8259002448a29f14855d58fe0a624ab76 b83e455451a875ba233b3b8ac29aff8b62f064f2 79cd993a623e101952b81fa6a29c674cd858504f (squashed to implement bssid_{white,black}lists) 0047306bc9ab7d46e8cc22ff9a3e876c47626473 (Add os_snprintf_error() helper) Signed-off-by:Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44438 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz format; .tar.bz2 are not provided anymore. - Add CONFIG_KEXEC_LZMA for selecting lzma support. Patches are updated along to: - Remove the now unnecessary patch 0004-mips_regdefs.patch. - Drop 100-reduce_size.patch because the size reduction is marginal. - Allow zlib and lzma support coexist together. This patch has been merged into upstream project. - Fix kexec-tools' configure.ac. - Fix a few compilation warnings. Size comparison of stripped binaries of kexec malta target with both zlib and lzma support enabled. - Before: 41447 - After: 42583 Signed-off-by:
Yousong Zhou <yszhou4tech@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44437 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
brcm2708: add missing config symbols and fix kernel modules for Raspberry Pi 2 by removing local version Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Thank you Dimitri for testing this. Signed-off-by:
-
blogic authored
- Allow --command-line parameters of kexec-tools be parsed and used by the kernel. - For malta machine, mark kernel code and kernel data segments as "System RAM" instead of "reserved" in /proc/iomem, otherwise kexec-tools will complain that program segments in ELF kernel file are invalid. Signed-off-by:
-
blogic authored
Signed-off-by:
Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44428 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
This patch adds corrected profile and build image for the TL-MR12U board. Unfortunately i cannot test the factory image since i can't find anywhere the original chinese firmware but the generated openwrt-ar71xx-generic-tl-mr12u-v1-squashfs-sysupgrade.bin worked just fine over a modified mr3040 factory image i managed to modify to initially flash the mr12u from the original firmware. Proper kernel support probably should be added since cat /proc/cpuinfo shows MR13U. Signed-off-by:
Daniel Petre <daniel.petre@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44427 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
This patch adds user-space support for the TL-MR12U board based on the mr13u patches. Signed-off-by:
-
blogic authored
ZyXEL NBG6716 add missing GPIO USB power on/off Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44425 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Feb 12, 2015
-
-
rmilecki authored
We obviously can't use sizeof(*buf) which is always 1. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44424 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nico authored
Signed-off-by:
-
luka authored
Add GoFlex Net "Board Name" , set and cleanup network default and LEDs. Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC. Signed-off-by:
L. D. Pinney <ldpinney@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44422 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
ZyXEL NBG6716 led/buttons cleanup - improper numbered leds - improper named buttons Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44417 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
-
rmilecki authored
Signed-off-by:
-
