- Aug 05, 2015
-
-
nbd authored
Remove options which have been moved into the generic config ever since. Signed-off-by:
Mathieu Olivari <mathieu@codeaurora.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46558 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
Old bootloader (same ones which have DT disabled) don't perform any PCIe initialization. The consequence is a freeze during PCIe bring-up on these old u-boot. Same kernel with a newer bootloaders works fine as they contain the corresponding PCIe init code. In this change, we'll add the missing init and make sure the kernel doesn't rely on some preexisting init to get PCIe to work. That includes the following changes: *GPIOs: set function & drive strength *Clocks: add init code for aux & ref clocks *PCIe driver: additional init of the hardware controller Tested 3.18 and 4.1 on an AP148 with bootloader branch 0.0.1 Signed-off-by:
-
nbd authored
PCIe controller nodes are numbers 0/1/2 in the chipset dtsi file, but the pinmux nodes are numbers 1/2/3. We'll make it consistent by changing the pinmux numbering to match the controller's one. Signed-off-by:
-
nbd authored
Certain AP148 platforms (and derivative) use bootloaders which did not have DT enabled. In order to support these old platforms, we'll now make the following modifications: *explicitely add the memory node in the AP148 DT: this used to be added by new u-boot through a run-time patch mechanism. We'll now add it explicitely so it works on boots which don't support that feature. New boots will have the node twice, the second one will be ignored. *add the zImage generation next to the FIT image for AP148. Other platforms using non-DT enabled bootloaders may want to leverage this zImage code to generate their own firmare as well. Signed-off-by:
-
nbd authored
Default kernel doesn't change and stays on 3.18 for now. Signed-off-by:
-
nbd authored
Signed-off-by:
Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46553 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Aug 02, 2015
-
-
nbd authored
Reported-by:
Steve Brown <sbrown@cortland.com> Signed-off-by:
Sven Eckelmann <sven@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46547 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
This patch fixes weak radio signal reported by nikola.georgiev Signed-off-by:
L. D. Pinney <ldpinney@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46545 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
The generic kernel cmdline parser ignores argv[0], this caused a regression for all lzma-loader based boards with linux 4.1 Signed-off-by:
-
- Aug 01, 2015
-
-
nbd authored
Signed-off-by:
-
- Jul 31, 2015
-
-
wigyori authored
Signed-off-by:
Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46539 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
nbd authored
Signed-off-by:
-
wigyori authored
Signed-off-by:
-
kaloz authored
Fix for default button states in WRT1900AC dts files. This prevents overlay wipe when reset is pressed. Signed-off-by:
Rob Mosher <nyt-openwrt@countercultured.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46530 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
wigyori authored
Signed-off-by:
-
kaloz authored
Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46527 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
wigyori authored
Signed-off-by:
-
wigyori authored
Signed-off-by:
-
wigyori authored
Signed-off-by:
-
- Jul 28, 2015
-
-
jow authored
Extend the SDK Config.in file to explicitely declare a MODULES symbol with the "option modules" flag set in order to prevent a kconfig segmentation fault whenever a "depends m" dependency is encountered. Signed-off-by:
Jo-Philipp Wich <jow@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46514 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Jul 26, 2015
-
-
hauke authored
This replaces the old patch with the version from Florian. Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46504 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
hauke authored
Signed-off-by:
-
hauke authored
Signed-off-by:
-
hauke authored
This activates CONFIG_MULTIUSER and sets the maximal number of cpus to 2. Signed-off-by:
-
nbd authored
Fixes low 5 GHz tx power issues Signed-off-by:
-
- Jul 25, 2015
-
-
hauke authored
This patch was missing for kernel 4.0 and 4.1 in r46464. I also replaced the version in OpenWrt with the version which went upstream into the Linux mainline kernel. This closes #20193 and #20192 Signed-off-by:
-
jogo authored
Switches BCM63xx to the new IB system. Images are generated per device definitions. There are no changes in the produced images except for some name changes, caused by the new IB system. Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46490 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
jogo authored
Simplify image/Makefile by using the new perl script for RedBoot. Signed-off-by:
-
jogo authored
REGMAP_MMIO is a hidden symbol, so it cannot be directly selected. If nothing selects it, it will fail the build with: ERROR: module '/store/buildbot/slave/slave/rb532/build/build_dir/target-mipsel_mips32_musl-1.1.10/linux-rb532/linux-3.18.19/drivers/base/regmap/regmap-mmio.ko' is missing. make[2]: *** [/store/buildbot/slave/slave/rb532/build/bin/rb532/packages/base/kmod-regmap_3.18.19-1_rb532.ipk] Error 1 Fix this by adding a description to allow selecting it manually. Fixes: r46451 ("kmod-regmap: enable MMIO support") Signed-off-by:
-
- Jul 24, 2015
-
-
nbd authored
Signed-off-by:
-
nbd authored
Signed-off-by:
-
blogic authored
Signed-off-by:
John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46477 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
Signed-off-by:
-
blogic authored
fixes #19816 Signed-off-by:
-
blogic authored
NCM specs are not actually mandating a specific position in the frame for the NDP (Network Datagram Pointer). However, some Huawei devices will ignore our aggregates if it is not placed after the datagrams it points to. Add support for doing just this, in a per-device configurable way. While at it, update NCM subdrivers, disabling this functionality in all of them, except in huawei_cdc_ncm where it is enabled instead. We aren't making any distinction between different Huawei NCM devices, based on what the vendor driver does. Standard NCM devices are left unaffected: if they are compliant, they should be always usable, still stay on the safe side. This change has been tested and working with a Huawei E3131 device (which works regardless of NDP position) and an E3372 device (which mandates NDP to be after indexed datagrams). Signed-off-by:
Enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by:
Matti Laakso <malaakso@elisanet.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46464 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46463 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
-
