- Jan 26, 2014
-
-
juhosg authored
Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39399 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Jan 25, 2014
-
-
juhosg authored
This ensures that the generated images will have enough erase blocks for JFFS2. Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Fix build errors caused by undefined 'usb_disable_xhci_ports' symbol. Signed-off-by:
-
- Jan 24, 2014
-
-
juhosg authored
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz interface are connected to GPIO lines. Because these GPIO lines are disabled by default, the RX sensitivity of the device is quite bad. Setup the GPIOs of the external LNAs to fix the issue. Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
It will be used for Compex devices. Signed-off-by:
-
juhosg authored
Signed-off-by:
-
luka authored
Recent lxc versions are not useful if this option is not enabled. That said, enable KERNEL_POSIX_MQUEUE by default when KERNEL_LXC_MISC is selected. Signed-off-by:
Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39385 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
juhosg authored
Get the size of the mtd partitions directly from the MTD layout and remove the superfluous macro parameters. Signed-off-by:
-
juhosg authored
The macro checks the size of the rootfs image even if the second parameter of the macro contains the size of an eraseblock. It is wrong because the size of the kernel image will be adjusted to the next eraseblock and the resulting image might be too large. Fix the macro to check the size of the final image instead of the rootfs image. Signed-off-by:
-
juhosg authored
This reverts r38197. The automatically created firmware partition includes the partition_table partition. Apart from the partition table, this partition contains sensitive data on some Compex devices which data can be destroyed when the firmware partition gets modified. Revert the change to prevent that. Signed-off-by:
-
luka authored
Signed-off-by:
-
- Jan 23, 2014
-
-
juhosg authored
Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by:
-
juhosg authored
Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
juhosg authored
Signed-off-by:
-
luka authored
Since that was the last configuration in defconfig directory we can drop the defconfig init script too. Signed-off-by:
-
luka authored
Signed-off-by:
-
cyrus authored
Thanks to Hans Dedecker for the fix. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39371 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
cyrus authored
Make the IPv4 "do not fragment" bit a configurable variable for the 6rd tunnel interface as the bit should not be set in the encapsulating IPv4 header according to RFC3056. On top the config variable allows to enable/disable path mtu discovery for tunnel interfaces. Config variable can be passed to netifd as tunnel config support is already present for the "do not fragment" bit. Signed-off-by:
Hans Dedecker <dedeckeh@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39370 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
juhosg authored
Fix build errors caused by undefined 'usb_disable_xhci_ports' symbol. Signed-off-by:
-
juhosg authored
Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
juhosg authored
The default inittab uses "askconsole" which is implemented by procd and uses the console provided by the kernel command line. Hence, this platform specific workaround is not necessary anymore. Signed-off-by:
-
- Jan 22, 2014
-
-
blogic authored
the fix horribly broke existing setups Signed-off-by:
John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39366 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Jan 21, 2014
-
-
blogic authored
make sure log buffer size is not bigger than the ubus message size Signed-off-by:
-
florian authored
Support for the BCM63268 is usable, enable it by default. Signed-off-by:
Florian Fainelli <florian@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39364 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
florian authored
Add kernel support for the BCM963269BHR board, USB and Ethernet switch, LEDs and buttons are working. Signed-off-by:
-
florian authored
Allow using the HSSPI controller since it works just fine, as well as the integrated switch core, since that one works too. Signed-off-by:
-
juhosg authored
Signed-off-by:
Felix Kaechele <heffer@fedoraproject.org> Patchwork: http://patchwork.openwrt.org/patch/4743/ Signed-off-by:
-
wigyori authored
Signed-off-by:
Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39360 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
wigyori authored
Signed-off-by:
-
wigyori authored
Signed-off-by:
-
jogo authored
The HIFN driver is a PCI driver, thus requires PCI support to be enabled to compile. Therefore let it depend on PCI.. Should fix mvebu builds. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39357 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
-
