Skip to content
Snippets Groups Projects
  1. Sep 11, 2014
  2. Sep 10, 2014
  3. Sep 09, 2014
  4. Sep 08, 2014
  5. Sep 07, 2014
    • nbd's avatar
      ath79: dev-eth: Don't advertise 1gbit in link code word on ar9331 · 870e6243
      nbd authored
      
      While the AR9331 has a gigabit MAC towards the internal switch, the
      integrated PHYs however are only 100-base-tx capable.  The existing code
      however advertieses gigabit capability in the link status word.  If you
      attach such a PHY to a gigabit capable switch on the remote end, with
      some probability it attempts to negotiate gigabit and fails, falling
      baco to the AR9331 assuming a 10mbit half-duplex link.  This has been
      observed quite frequently with the Carambola2 and gigabit capable
      switches.
      
      In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
      for both AR9331 ethernet ports. This is most likely wrong. Despite the
      two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
      100base-T PHY via MII. The has_gbit attribute is used in the ethernet
      driver to determine the supported link modes.
      
      So either pdata->has_gbit is not set to 1 anymore, or the ethernet
      driver needs to be modified to determine the advertised link code word
      on another criteria than pdata->has_gbit.  This patch implements the
      former solution.
      
      Signed-off-by: default avatarHarald Welte <laforge@gnumonks.org>
      
      git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42432 3c298f89-4303-0410-b956-a3cf2f4a3e73
      870e6243
    • jogo's avatar
      mac80211: enable DFS support for ath9k/10k by default · 24365c6b
      jogo authored
      
      The DFS pattern detector now supports all three regions; ETSI, FCC and
      JP, so there is no reason to not have it enabled anymore.
      
      Signed-off-by: default avatarJonas Gorski <jogo@openwrt.org>
      
      git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42431 3c298f89-4303-0410-b956-a3cf2f4a3e73
      24365c6b
    • jogo's avatar
      toolchain/binutils: do not install host libiberty.a into target lib dir · 28c3e50b
      jogo authored
      
      Binutils target build will pick it up and break build on e.g. arm:
      
      libtool: link: arm-openwrt-linux-uclibcgnueabi-gcc -shared  .libs/archive.o .libs/archures.o .libs/bfd.o .libs/bfdio.o .libs/bfdwin.o .libs/cache.o .libs/coffgen.o .libs/corefile.o .libs/format.o .libs/init.o .libs/libbfd.o .libs/opncls.o .libs/reloc.o .libs/section.o .libs/syms.o .libs/targets.o .libs/hash.o .libs/linker.o .libs/srec.o .libs/binary.o .libs/tekhex.o .libs/ihex.o .libs/stabs.o .libs/stab-syms.o .libs/merge.o .libs/dwarf2.o .libs/simple.o .libs/compress.o .libs/verilog.o .libs/elf32-arm.o .libs/elf32.o .libs/elf-nacl.o .libs/elf-vxworks.o .libs/elf.o .libs/elflink.o .libs/elf-attrs.o .libs/elf-strtab.o .libs/elf-eh-frame.o .libs/dwarf1.o .libs/elf32-gen.o .libs/cpu-arm.o   -L/mnt/dl/slave/at91/build/staging_dir/target-arm_arm926ej-s_uClibc-0.9.33.2_eabi/usr/lib -L/mnt/dl/slave/at91/build/staging_dir/target-arm_arm926ej-s_uClibc-0.9.33.2_eabi/lib -L/mnt/dl/slave/at91/build/staging_dir/toolchain-arm_arm926ej-s_gcc-4.8-linaro_uClibc-0.9.33.2_eabi/usr/lib -L/mnt/dl/slave/at91/build/staging_dir/toolchain-arm_arm926ej-s_gcc-4.8-linaro_uClibc-0.9.33.2_eabi/lib -L/mnt/dl/slave/at91/build/build_dir/target-arm_arm926ej-s_uClibc-0.9.33.2_eabi/binutils-2.24/bfd/../libiberty/pic -liberty -lz  -march=armv5te -mtune=arm926ej-s -mfloat-abi=soft -Wl,-lc -Wl,--as-needed -Wl,-lm -Wl,--no-as-needed   -Wl,-soname -Wl,libbfd-2.24.so -o .libs/libbfd-2.24.so
      /mnt/dl/slave/at91/build/staging_dir/toolchain-arm_arm926ej-s_gcc-4.8-linaro_uClibc-0.9.33.2_eabi/lib/libiberty.a: could not read symbols: File format not recognized
      
      Signed-off-by: default avatarJonas Gorski <jogo@openwrt.org>
      
      git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42430 3c298f89-4303-0410-b956-a3cf2f4a3e73
      28c3e50b
  6. Sep 06, 2014
Loading