- Jul 16, 2015
-
-
jogo authored
Now that we have a BuildDTB command, make use of it instead of calling dtc directly. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46390 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Jul 14, 2015
-
-
blogic authored
To improve reproducibility, prevent the inclusion of timestamps in the gzip header. Signed-off-by:
Reiner Herrmann <reiner@reiner-h.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46361 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Jun 11, 2015
-
-
jogo authored
When r42245 moved A4001N to DT based detection the image padding size was accidentally increased from 4 to 8 MiB. This made images unflashable on these devices. Fixes #19836. Signed-off-by:
-
- Jun 02, 2015
-
-
jogo authored
Livebox does need the uncompressed kernel, so just create it during image generation. Signed-off-by:
-
- Jun 01, 2015
-
-
jogo authored
Delete the dtb appended, uncompressed kernels after having compressed them, so they don't end in the image builder. Signed-off-by:
-
- May 27, 2015
-
-
jow authored
Also remove "redbootscript" and "redbootscript.padded" junk files. Signed-off-by:
Jo-Philipp Wich <jow@openwrt.org> Acked-by:
-
- May 21, 2015
-
-
jogo authored
This patch adds support for the Huawei HG655b. Nothing much special in this router, it's just another BCM6368 with a Ralink RT3062 wifi chip and the calibration data embedded in the main flash chip at offset 0x7c0000. There is also configuration data used by the OEM firmware before the cal_data partition, this area is protected by the board_data partition in this patch. Signed-off-by:
Daniel Gonzalez <dgcbueu@gmail.com> Signed-off-by:
-
- Apr 21, 2015
-
-
jogo authored
Hopefully the last missing board. Signed-off-by:
-
- Mar 31, 2015
-
-
jogo authored
Accidentally left over development artifact. Reported-by:
John Crispin <blogic@openwrt.org> Signed-off-by:
-
- Mar 30, 2015
-
-
jogo authored
Now that all supported boards have an dts there is no need for a dtb free kernel anymore. Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Also readd image generation which was accidentally dropped in r43364. Signed-off-by:
-
jogo authored
Appearently the kernel only uses kernel above it, so moving it to an higher address causes a lot of unavailable memory (#19327). Also move the on-flash kernel to 0x80a0000, as newer CFEs don't like uncompressing there (net-booting an ELF kernel is fine, though). Signed-off-by:
-
- Mar 25, 2015
-
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Also build image again(?). Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Support for the BT HomeHub 2.0 Type A. This router was manufactured by Thomson, and it's BCM6358 based. The leds are controled by two chained HC594, all working ok. The BCM5325 switch has the RESET# pin wired to the GPIO15, but currently there is no way to tell the b53 driver how to get this gpio number in brcm63xx, therefore swconfig won't use it when performing a switch reset. The patch was tested with several firmwares, and all except unsupported stuff (i.e xDSL) works pretty well. Tested-by:
Tahir <tahir00ali@gmail.com> Signed-off-by:
-
jogo authored
Fixes boot when uncompressed kernel is > 4 MiB (#19251). Signed-off-by:
-
jogo authored
Respect the vmlinux load address when generating images. Signed-off-by:
-
jogo authored
Currently there isn't images ready for flashing liveboxes boards. This patch adds a script and the code to call it in the bcm63xx images builder makefile to generate the livebox 1 firmware. I removed some lines to avoid generating unneded files in the bin/ dir for this board. And added code to generate a squashed rootfs aligned to 64 kB since the current one in the /bin dir is 128 kB aligned and doesn't work. Still no sysupgrade support for this board. Upgrading from within openwrt can be done writing with mtd the kernel, and then the 64k aligned rootfs. Regards Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
All images generated contain dtbs, so it is now unused. Signed-off-by:
-
- Mar 16, 2015
-
-
jogo authored
This adds support for the Netgear DGND3700 v1 and DGND3800B. DGND3700 v1 and DGND3800B are exactly the same router, only one difference, the factory firmware. This patch produces two factory firmwares for each router. The router includes an onboard NAND flash for extra storage. NAND is currently not supported in bcm63xx, so no code added for this part. The NOR flash (32MB) is enough for storing an openwrt firmware. Signed-off-by:
-
- Feb 28, 2015
-
-
jogo authored
Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@44569 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Feb 27, 2015
-
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Add a dtsi for bcm3368, add a dts and profile for cvg834g, and convert it to use ImageDTB. Since HCS requires more arguments, enhance the max arguments of the call. The image name is intentionally left blank to prevent non-initramfs images to be built, as they currently contain no rootfs and consequently won't work. Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
jogo authored
Most 16 MiB RAM devices don't even load elf kernels, so it's safe to assume we have at least 32 MB RAM. This fixes tftp booting with the default package set as this already produces an uncompressed kernel > 8 MiB. New limit is 8 MiB compressed / 24 MiB compressed. Signed-off-by:
-
jogo authored
We do not need to align the start of read only rootfs's to erase blocks. This allows us to write the squashfs rootfs directly behind the kernel, potentially freeing up one erase block. We still need to align for jffs2, so add a flag for imagetag to optionally align the rootfs start. Signed-off-by:
-
jogo authored
We do not use the result, so no need to call it. Signed-off-by:
-
- Dec 08, 2014
-
-
jogo authored
Signed-off-by:
-
jogo authored
Signed-off-by:
-
