- Aug 23, 2015
-
-
jogo authored
Fix patches not applying anymore since r46654. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46714 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
jogo authored
Changelog: * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.6 Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46713 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
jogo authored
Properly treat -ENOSYS as no PHY, else ehci-orion won't work without generic phy support. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46711 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
jogo authored
Some CFEs seem to misconfigure the mapped memory flash access with fast read but without a dummy byte, causing all accesses to be prefixed with 0xff. This of course breaks reading out the nvram, so do not just move back to single i/o accessors, but also ensure that the dummy byte is correctly set. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46707 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Aug 21, 2015
-
-
wigyori authored
Signed-off-by:
Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46705 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
wigyori authored
Signed-off-by:
Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46704 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
wigyori authored
Signed-off-by:
Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46703 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
wigyori authored
Signed-off-by:
Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46702 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
kaloz authored
problems. Now that the switch driver can handle two devices with the same MAC address in separate VLANs we can go back to using the same address on both interfaces. This is the Linksys firmware's default behavior. Signed-off-by:
Claudio Leite <leitec@staticky.com> Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46700 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
kaloz authored
a single database in the ATU. This created problems in the case of a system where two ports/devices share a MAC address (e.g. Linksys WRT1900AC eth0/eth1). This also clears any bootloader-set FDB defaults. This had caused issues creating port-based VLANs when mappings overlapped previous VLANs. Packets destined to a port not in the default port group flooded all ports. Tested on a 88E6171 (Linksys EA4500) and 88E6172 ('1900AC) Signed-off-by:
Claudio Leite <leitec@staticky.com> Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46699 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
kaloz authored
Thanks Sebastian for spotting it. Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46697 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
wigyori authored
Signed-off-by:
Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46696 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Aug 19, 2015
-
-
kaloz authored
The u-boot boot counter was never reset after a successful boot, which sometimes could make some variables become out of sync. This patch adds support for the boot counter and enables auto_recovery unconditionally. Signed-off-by:
Jonas Gorski <jogo@openwrt.org> Signed-off-by:
Rob Mosher <nyt-openwrt@countercultured.net> Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46690 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
- Aug 17, 2015
-
-
blogic authored
The patch submitted in [46649] was mangled in the use of gmails webmail interface, tabs replaced with spaces, resulting in a patch which dit not apply. This should fix the issue, sorry for the noise. Signed-off-by:
Ben Whitten <benwhitten@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46676 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
no-op since 2.6.35 removed in Kernel 4.1 see https://lwn.net/Articles/380931/ Signed-off-by:
Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46672 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
no-op since 2.6.35 removed in Kernel 4.1 see https://lwn.net/Articles/380931/ Signed-off-by:
Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46671 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's PHY driver (for his u-boot sources) already supports that PHY because it uses a PHY ID mask of 0xfffffff8. Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46670 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46668 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
0073 needs to applied afert 0102 Signed-off-by:
John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46667 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Instead of using board name provided explicitly as text in LED name, ex.: [...] mlwg2) status_led="mlwg2:blue:system" [...] use $board variable, which allows to combine together multiple boards with same color and LED names, ex: [...] mlw221|\ mlwg2) status_led="$board:blue:system" [...] The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically. One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name"). Signed-off-by:
Piotr Dymacz <pepe2k@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46665 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach. The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target: * fixes wrong indentation * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body) * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files) * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds) Signed-off-by:
Piotr Dymacz <pepe2k@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46664 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
Weijie Gao <hackpascal@gmail.com> This patch adds support for TP-Link TL-WDR6500 v2. The firmware has a U-Boot header for kernel, and a TP-LINK v2 header for the whole firmware, so I have to create a new firmware creation method. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46663 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
Weijie Gao <hackpascal@gmail.com> This patch adds flash layout parser for TP-Link firmwares which have a 64kb bootloader. This is used for TP-Link TL-WDR6500 v2. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46662 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46660 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46659 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
*Enable SMEM MTD parser and its dependencies (SMEM & HW spinlocks) in the kernel config *Replaces the MTD layout in DT by the dynamic layout provided by the SMEM parser for AP148 Using the OF based parser is still possible on platforms which have a fixed MTD partition layout. Signed-off-by:
Mathieu Olivari <mathieu@codeaurora.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46658 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
This patch adds a new parser which uses the SMEM available on IPQ and some other QCOM platforms to map the MTD partitions. Signed-off-by:
Mathieu Olivari <mathieu@codeaurora.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46657 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
2 patches are cherry-picked from the following LKML thread: *https://lkml.org/lkml/2015/4/11/208 The last patch (036-soc-qcom-add-smem-to-IPQ806x-platforms.patch) is adding the corresponding DT nodes required for IPQ806x. Signed-off-by:
Mathieu Olivari <mathieu@codeaurora.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46656 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
This change cherry-picks the following 3 changes from linux-next: *fb7737 hwspinlock/core: add device tree support *19a0f6 hwspinlock: qcom: Add support for Qualcomm HW Mutex block *bd5717 hwspinlock: qcom: Correct msb in regmap_field We're also adding a patch to add the hardware spinlock device nodes on IPQ806x platforms (033-soc-qcom-Add-sfbp-device-to-IPQ806x-dts.patch). Signed-off-by:
Mathieu Olivari <mathieu@codeaurora.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46655 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
The "linux,part-probe" dts parsing is a pretty neat generic feature. It has been posted to kernel.org and could easily be reused by all targets. This change moves the patch to the 3.18 and 4.1 generic folders, and makes the feature available to all platforms who may want to use it. Signed-off-by:
Mathieu Olivari <mathieu@codeaurora.org> Acked-by:
Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46654 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Add support for the Black Swift board: http://www.black-swift.com/ Took relevant parts and slightly adapted from: https://github.com/blackswift/openwrt/blob/master/bsb.patch Signed-off-by:
Bruno Randolf <br1@einfach.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46651 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
This patch is backport of a fix to a USB prototype mismatch bug found in 3.18 kernels, originally submitted by Boris Brezillon [1]. The symptom of this bug was that devices attached to the at91 using at91_ohci on a hub never appeared and failed to initialise. [1] http://www.spinics.net/lists/linux-usb/msg125969.html Signed-off-by:
Ben Whitten <ben.whitten@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46649 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
to avoid editing the dts every time the kernel size changes. uImage is now bigger than 1MB. Pad uImage to 64k erase block size. Signed-off-by:
Günther Kelleter <guenther.kelleter@devolo.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46648 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Switch to generich chip irqs/irq domains. Interrupts were broken since kernel 3.14. dLAN USB extender is now booting again. Signed-off-by:
Günther Kelleter <guenther.kelleter@devolo.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46647 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Switch to new 8250 debug uart code because the old mach-mcs814x/include/mach/debug-macro.S tries to include asm/hardware/debug-8250.S which no longer exists since kernel 3.14 Signed-off-by:
Günther Kelleter <guenther.kelleter@devolo.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46646 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
The MT7621 uses a 2 bit wide configuration of the sdhci, spi, mdio, pcie, wdt, uart2 and uart3 in the GPIO_MODE register. It was correctly done for sdhci, spi, pcie and wdt, The same has to be done for uart3, uart2 and mdio. Signed-off-by:
Sven Eckelmann <sven@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46645 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
The PINS conntrolled by the SPI bits in the GPIO_MODE register is always 7 and not 8 for nand mode. Signed-off-by:
Sven Eckelmann <sven@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46644 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
The uart3 setting in GPIO_MODE register is before the uart2 setting. Also don't mix uart2 and uart3 function/groups. Signed-off-by:
Sven Eckelmann <sven@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46643 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46642 3c298f89-4303-0410-b956-a3cf2f4a3e73
-
blogic authored
Signed-off-by:
Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@46641 3c298f89-4303-0410-b956-a3cf2f4a3e73
-